Advanced Search
DSpace@MIT

A Super Critical Carbon Dioxide Cycle for Next Generation Nuclear Reactors

Research and Teaching Output of the MIT Community

Show simple item record

dc.contributor.author Dostal, Vaclav
dc.contributor.author Driscoll, Michael J.
dc.contributor.author Hejzlar, Pavel
dc.contributor.other Advanced Nuclear Power Technology Program (Massachusetts Institute of Technology) en_US
dc.date.accessioned 2011-12-14T18:01:13Z
dc.date.available 2011-12-14T18:01:13Z
dc.date.issued 2004-03
dc.identifier.uri http://hdl.handle.net/1721.1/67671
dc.description.abstract A systematic, detailed major component and system design evaluation and multiple-parameter optimization under practical constraints has been performed of the family of supercritical CO[subscript 2] Brayton power cycles for application to advanced nuclear reactors. The recompression cycle is shown to excel with respect to simplicity, compactness, cost and thermal efficiency. The main advantage of the supercritical CO[subscript 2] cycle is comparable efficiency with the helium Brayton cycle at significantly lower temperature (550ºC vs. 850ºC, but higher pressure (20 MPa vs. 8 MPa). The supercritical CO[subscript 2] cycle is well suited to any type of nuclear reactor with core outlet temperature above ~ 500ºC in either direct or indirect versions. By taking advantage of the abrupt property changes near the critical point of CO[subscript 2] the compression work can be reduced, which results in a significant efficiency improvement. However, a real gas cycle requires much more careful optimization than an ideal gas Brayton cycle. Previous investigations by earlier authors were systematized and refined in the present work to survey several different CO[subscript 2] cycle layouts. Inter-cooling, re-heating, re-compressing and pre-compressing were considered. The recompression cycle was found to yield the highest efficiency, while still retaining simplicity. Inter-cooling is not attractive for this type of cycle as it offers a very modest efficiency improvement. Re-heating has a better potential, but it is applicable only to indirect cycles. Economic analysis of the benefit of re-heating for the indirect cycle showed that using more than one stage of re-heat is economically unattractive. For the basic design, turbine inlet temperature was conservatively selected to be 550ºC and the compressor outlet pressure set at 20 MPa. For these operating conditions the direct cycle achieves 45.3% thermal efficiency and reduces the cost of the power plant by ~18% compared to a conventional Rankine steam cycle. The capital cost of the basic design compared to a helium Brayton cycle is about the same, but the supercritical CO[subscript 2] cycle operates at significantly lower temperature. The current reactor operating experience with CO[subscript 2] is up to 650ºC, which is used as the turbine inlet temperature of an advanced design. The thermal efficiency of the advanced design is close to 50% and the reactor system with the direct supercritical CO[subscript 2] cycle is ~24% less expensive than the steam indirect cycle and 7% less expensive than a helium direct Brayton cycle. It is expected in the future that high temperature materials will become available and a high performance design with turbine inlet temperatures of 700ºC will be possible. This high performance design achieves a thermal efficiency approaching 53%, which yields additional cost savings. The turbomachinery is highly compact and achieves efficiencies of more than 90%. For the 600 MWth/246 MWe power plant the turbine body is 1.2 m in diameter and 0.55 m long, which translates into an extremely high power density of 395 MWe/m3. The compressors are even more compact as they operate close to the critical point where the density of the fluid is higher than in the turbine. The power conversion unit that houses these components and the generator is 18 m tall and 7.6 m in diameter. Its power density (MWe/m3) is about ~ 46% higher than that of the helium GT-MHR (Gas Turbine Modular Helium Reactor). A by-pass control scheme is shown to be applicable to the supercritical CO[subscript 2] cycle and exhibits an almost linear efficiency decrease with power. The use of inventory control is difficult since it controls the cycle by changing the operating pressure, which changes the split of the flow between two compressors that work in parallel. The change is so significant that the compressors cannot cope with it. This is mainly because of the current cycle design with a single shaft synchronized with the grid, which was chosen in order to simplify the plant layout, the start-up procedure and eliminate the need for a start up motor. Multiple shaft layouts or compressors with adjustable blade geometry would be necessary to overcome this problem. Since these modifications would increase the capital cost of the system they are not pursued in the present work, which emphasizes base-load performance. en_US
dc.description.sponsorship Idaho National Engineering and Environmental Laboratory en_US
dc.description.sponsorship Argonne National Laboratory en_US
dc.description.sponsorship United States. Dept. of Energy en_US
dc.publisher Massachusetts Institute of Technology. Center for Advanced Nuclear Energy Systems. Advanced Nuclear Power Program en_US
dc.relation.ispartofseries MIT-ANP;PR-100
dc.title A Super Critical Carbon Dioxide Cycle for Next Generation Nuclear Reactors en_US
dc.type Technical Report en_US
dc.contributor.mitauthor Dostal, Vaclav
dc.contributor.mitauthor Driscoll, Michael J.
dc.contributor.mitauthor Hejzlar, Pavel
dspace.orderedauthors Dostal, Vaclav; Driscoll, Michael J.; Hejzlar, Pavel en_US


Files in this item

Name Size Format Description
ANP-100.pdf 7.856Mb PDF

This item appears in the following Collection(s)

Show simple item record

TechReports