Show simple item record

dc.contributor.advisorEvelyn N. Wang.en_US
dc.contributor.authorKelsall, Colin Clancyen_US
dc.contributor.otherMassachusetts Institute of Technology. Department of Mechanical Engineering.en_US
dc.date.accessioned2019-02-05T15:17:39Z
dc.date.available2019-02-05T15:17:39Z
dc.date.copyright2018en_US
dc.date.issued2018en_US
dc.identifier.urihttp://hdl.handle.net/1721.1/120194
dc.descriptionThesis: S.M., Massachusetts Institute of Technology, Department of Mechanical Engineering, 2018.en_US
dc.descriptionThis electronic version was submitted by the student author. The certified thesis is available in the Institute Archives and Special Collections.en_US
dc.descriptionCataloged from student-submitted PDF version of thesis.en_US
dc.descriptionIncludes bibliographical references (pages 63-64).en_US
dc.description.abstractSolar energy has been an important component of the world's energy infrastructure for many years, but certain limitations have hindered its ability to become a primary source of renewable energy. In particular, intermittency and fundamental limitations on conversion efficiency have restricted adoption of direct photovoltaic conversion with PV cells. Recent developments in more advanced cell chemistries and concentrated solar power systems (CSP) seek to address some of these limitations and enable higher grid penetration of solar derived power. This thesis examines one of these such technologies, solar thermophotovoltaics (STPV), and presents opportunities to improve on past work in the field to enable higher conversion efficiencies and lower cost solar power. STPV power systems typically utilize a monolithic absorber-emitter component that is heated with concentrated sunlight through a highly absorptive surface. The monolith radiatively illuminates a low-bandgap PV cell from a different, spectrally selective emitter surface, producing electricity. This added spectral selectivity allows for improved photovoltaic conversion efficiencies compared to a standard PV cell illuminated with the solar spectrum. STPV systems, however, often operate above 1000°C and are hindered by substantial parasitic thermal losses. In this thesis we first present an overview of the loss mechanisms currently limiting STPV system efficiencies and some theoretical approaches to address these losses. Previously demonstrated STPV systems have significant drops in efficiency through re-emission losses from the hot absorber surface. Selective absorber coatings can reduce these losses; however, experimentally demonstrated efficiency improvements have been limited due to non-ideal spectral selectivity and high-temperature instability. Through an alternative approach, we present a purely geometric solution to mitigate re-emission losses by varying the area ratio, defined as the ratio of thermal emitter area to solar absorber area. We model how our solution could theoretically improve previously demonstrated STPV systems and also discuss the practical limitations of our approach. Secondly, we investigate the potential of integrating a cavity-based geometry for the absorber-emitter monolith in place of typical planar designs. By incorporating a cavity in place of the planar absorber-emitter, we take advantage of both increased absorption across the full solar spectrum and enable very high area ratios in a compact design. Third, we address how thermal gradients might develop within the absorber-emitter monolith and how these gradients might impact system performance. We present a numerical model capable of predicting PV cell performance degradation under uneven illumination resulting from emitter temperature gradients. Finally, we validate our model through experiments using cavities made from high-temperature refractory materials and a high-powered laser to emulate highly concentrated sunlight. By integrating a cavity-type absorber-emitter with state-of-the-art spectrally selective surfaces and filters, the maximum system efficiency demonstrated in previous works could be increased from 6.8% to upwards of 9% without any improvements in spectral selectivity. This cavity-type approach, which has the potential to improve solar absorber performance both for STPV and other solar thermal technologies, could help realize the full potential of these systems as efficient and useful methods of solar energy conversion.en_US
dc.description.statementofresponsibilityby Colin Clancy Kelsall.en_US
dc.format.extent65 pagesen_US
dc.language.isoengen_US
dc.publisherMassachusetts Institute of Technologyen_US
dc.rightsMIT theses are protected by copyright. They may be viewed, downloaded, or printed from this source but further reproduction or distribution in any format is prohibited without written permission.en_US
dc.rights.urihttp://dspace.mit.edu/handle/1721.1/7582en_US
dc.subjectMechanical Engineering.en_US
dc.titleCavity absorber-emitters for high-temperature solar thermophotovoltaicsen_US
dc.typeThesisen_US
dc.description.degreeS.M.en_US
dc.contributor.departmentMassachusetts Institute of Technology. Department of Mechanical Engineering
dc.identifier.oclc1083126312en_US


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record