2026-09-19T16:21:51Zhttps://dspace.mit.edu/server/oai/request

oai:dspace.mit.edu:1721.1/442922022-01-13T07:54:19Zcom_1721.1_7582com_1721.1_7581col_1721.1_131023

Karen K. Gleason. Lee, Long Hua Massachusetts Institute of Technology. Dept. of Chemical Engineering. Massachusetts Institute of Technology. Department of Chemical Engineering 2009-01-30T16:29:05Z 2009-01-30T16:29:05Z 2007 2007 http://hdl.handle.net/1721.1/44292 272354600 Thesis (S.M.)--Massachusetts Institute of Technology, Dept. of Chemical Engineering, 2007. Includes bibliographical references (leaves 81-83). P(neopentyl methacrylate-co-ethylene glycol dimethacrylate) copolymer, abbreviated as P(npMAco-EGDA), was selected as the potential air-gap sacrificial material among possible combination of twenty monomers and four crosslinkers. P(npMA-co-EGDA) was deposited onto substrates using initiated chemical vapor deposition (iCVD) technique. Spectroscopic data showed the effective incorporation of both components in the copolymer and the integrity of repeating units were retained. The onset temperature of decomposition of P(npMA-co-EGDA) copolymer could be tuned between 290-3500C by varying the composition of the copolymer. The removal rate of polymer was calculated based on interferometry signal-time curve. The activation energy was determined by fitting the rate of decomposition with logistic model and found to be 162.7+8kJ/mole, which was similar to published data. Flash pyrolysis gas chromatography mass spectroscopy analysis showed that the products of thermal decomposition are monomers, rearranged small molecules and low oligomers. The modulus and the hardness were in the range of 3.9 to 5.5 GPa and 0.38 to 0.75 GPa, respectively, and were higher than those of linear poly(methyl methacrylate) (PMMA). Air-gap structures were constructed in the following scheme: P(npMA-co-EGDA) was deposited on the substrate by iCVD, followed by spincasting PMMA electron beam resist and scanning electron beam lithography to implement patterns on the resist. Reactive ion etching (RIE) was then applied to simultaneously etch the PMMA resist and P(npMA-co-EGDA) sacrificial material away in a controlled manner, leaving the patterned sacrificial material on the substrate. (cont.) A layer of porous silica was deposited to cover the substrate and the patterned sacrificial material by plasma-enhanced chemical vapor deposition (PECVD) at 2500C and the sample was thermally annealed to allow the decomposed fragments to diffuse through the overlayer of silica. Using the scheme described above, it was possible to construct air-gap structures with feature size of 200nm and feature height of 1 00nm. by Long Hua Lee. S.M. 83 leaves eng Massachusetts Institute of Technology M.I.T. theses are protected by copyright. They may be viewed from this source for any purpose, but reproduction or distribution in any format is prohibited without written permission. See provided URL for inquiries about permission. http://dspace.mit.edu/handle/1721.1/7582 Chemical Engineering. Air-gap sacrificial materials by initiated chemical vapor deposition Thesis application/pdf false Publication unknown unknown <Publication xmlns="https://www.openaire.eu/cerif-profile/1.1/" id="6a1f0102-d16c-40c2-9621-1d255ef3668b"> <Type xmlns="https://www.openaire.eu/cerif-profile/vocab/COAR_Publication_Types">http://purl.org/coar/resource_type/c_1843</Type> <Language>eng</Language> <Title>Air-gap sacrificial materials by initiated chemical vapor deposition</Title> <PublishedIn> <Publication> </Publication> </PublishedIn> <PublicationDate>2007</PublicationDate> <Authors> <Author> <DisplayName>Lee, Long Hua</DisplayName> <Affiliation> <OrgUnit> </OrgUnit> </Affiliation> </Author> </Authors> <Editors> </Editors> <Publishers> <Publisher> <DisplayName>Massachusetts Institute of Technology</DisplayName> <OrgUnit /> </Publisher> </Publishers> <License>http://dspace.mit.edu/handle/1721.1/7582</License> <Keyword>Chemical Engineering.</Keyword> <Abstract>P(neopentyl methacrylate-co-ethylene glycol dimethacrylate) copolymer, abbreviated as P(npMAco-EGDA), was selected as the potential air-gap sacrificial material among possible combination of twenty monomers and four crosslinkers. P(npMA-co-EGDA) was deposited onto substrates using initiated chemical vapor deposition (iCVD) technique. Spectroscopic data showed the effective incorporation of both components in the copolymer and the integrity of repeating units were retained. The onset temperature of decomposition of P(npMA-co-EGDA) copolymer could be tuned between 290-3500C by varying the composition of the copolymer. The removal rate of polymer was calculated based on interferometry signal-time curve. The activation energy was determined by fitting the rate of decomposition with logistic model and found to be 162.7+8kJ/mole, which was similar to published data. Flash pyrolysis gas chromatography mass spectroscopy analysis showed that the products of thermal decomposition are monomers, rearranged small molecules and low oligomers. The modulus and the hardness were in the range of 3.9 to 5.5 GPa and 0.38 to 0.75 GPa, respectively, and were higher than those of linear poly(methyl methacrylate) (PMMA). Air-gap structures were constructed in the following scheme: P(npMA-co-EGDA) was deposited on the substrate by iCVD, followed by spincasting PMMA electron beam resist and scanning electron beam lithography to implement patterns on the resist. Reactive ion etching (RIE) was then applied to simultaneously etch the PMMA resist and P(npMA-co-EGDA) sacrificial material away in a controlled manner, leaving the patterned sacrificial material on the substrate.</Abstract> <Abstract>(cont.) A layer of porous silica was deposited to cover the substrate and the patterned sacrificial material by plasma-enhanced chemical vapor deposition (PECVD) at 2500C and the sample was thermally annealed to allow the decomposed fragments to diffuse through the overlayer of silica. Using the scheme described above, it was possible to construct air-gap structures with feature size of 200nm and feature height of 1 00nm.</Abstract> <Access xmlns="http://purl.org/coar/access_right" > </Access> </Publication>